SPECIFICATIONS

  • MakeChevrolet
  • ModelCamaro
  • Year1967
  • Serial #132178
  • VIN124377L132178
  • Engine TypeDonovan 400
  • Chassis TypeUnibody
  • Body TypeCoupe
  • Body BuilderFisher
  • Current LocationFerraris-Online LLC

We are pleased to offer 1967 Camaro s/n 132178, a money-is-no-object 1967 Camaro that was seriously prepared for the Pike’s Peak Hill climb by Absolute Engineering, Goleta, CA at a hard-parts cost of well over $100,000 yet is street registered with a Montana title and plates. Power comes from an aluminum 6.6 liter (400 C.I.D.) Donovan 350/400 small block # 44314 P fitted with a forged steel Scat 3.75 crank and Oliver forged steel connecting rods; 4.125 Mahle pistons and an Edelbrock Total Power Package featuring aluminum Edelbrock Victor Jr. 64cc cylinder heads; an SBC 23-Degree Victor Jr. 64cc roller tappet cam and a matched Edelbrock RPM intake manifold topped-of with a Holley XP 850 CFM Double Pump carburetor. Spark come from a MSD Pro-billet distributor with an MSD spark box with a built in changeable rev-limiter feeding to an MSD HBC Blaster coil and MSD Ignition wires while an ATi Super Damper makes checking the timing easy. A massive baffled aluminum oil pan provides the lubrication. Fabricated aluminum valve covers with an overflow oil catch can and a breather air filter top off the upper end. Total power is over 500 hp. Engine power is fed into a Tilton flywheel and multi-disc ceramic clutch to an Autogear/Muncie M23 close-ratio transmission with a heavy-duty Autogear case with interchange gear ratios and a Hurst long shifter. That power is sent down the drive train through an Aluminum DriveShaftPro driveshaft to a fully rebuilt 3:55 rear end by Coastal Differential, Ventura, CA.

Starting power comes from a lightweight racing battery and Tilton starter motor. Engine cooling is by a NASCAR style aluminum radiator with its matching aluminum overflow surge tank and a high volume water pump. Oil cooling is done with a large Setrab oil cooler with an impressively machined remote oil filter. Doug’s headers with an all-new Borla muffler and pipe system handle the exhaust. A lightweight PowerMaster alternator keeps everything charged and an ancillary SPAL radiator fan keeps it all cool. Power and braking are put to the ground through a fully rebuilt suspension with all new Delrin/Aluminum suspension bushings and four wheel disc brakes fitted with Wilwood brake calipers and all new brake mounting and suspension hardware. A set of Koni shocks fitted with all new hardware help keep it firmly planted. A full new set of 15″ X 8″ Torq-Thrust wheels with Hoosier 245/50ZR-15 race tires put the rubber to the ground.

The interior is fitted with a full roll cage, dual lightweight Momo race seats, a six-point Schroth safety harness and a Longacre steering wheel. A full set of new AutoMeter oil pressure, oil temperature, tach, water temp, voltage, MPH and fuel level gauges with an oil pressure and water temperature warning light keep everything in check. A nicely mounted ESS firebottle with cockpit, trunk and engine retardant nozzles help keep it safe while all the right switchgear is properly marked and is mounted easy to access. A very nicely made fuse and relay board keep the electrons going to the right places and the cockpit wiring harness is nicely sleeved and finished. A 22-gallon ATL fuel cell with a new Edelbrock 160 GPH pump and all new Aeroquip lines provide the fuel. An X2 Racekey transponder is also fitted.

The entire outer, inner and lower body were stripped out and treated to excellent and all-new race-quality paint in an attractive medium blue with dual medium-green race stripes. The body and panel fit is excellent. The interior compartment, the under hood compartment, the floor, chassis and trunk have all been finished in light grey while both doors were substantially lightened and fitted with cleverly made outside door latches. The lower front is fitted with a splitter to keep air from under the car at speed. All new headlight and tail lights assemblies were installed as needed for road racing. New and nicely fitted plexiglass front and rear windscreens are installed with clever rubber shock mounting. A lightweight lift-off and pinned fiberglass hood, trunk and trunk rear spoiler have been fitted. All the necessary tow hooks are nicely machined and fitted. Total weight is only 2,400 lbs. We have detailed photos showing the complete build process, e-mail us if you would like copies by e-mail.

1967 Camaro s/n 132178 was fully rebuilt for Pike’s Peak and is now offered at far less than the component and build cost. Every component on s/n 132178 is new and never raced and only need final sorting and testing, as does any racecar going to a new owner. Thanks to its 500 plus hp 6.6 liter (400 C.I.D.) Donovan aluminum small block and its stripped out body at 2,400 lbs s/n 132178 is outrageously powerful and with minor tweaks can run in HSR, VARA, NASA, Targa Newfoundland or any other such similar event or series. Because s/n 132178 is a 1967 year model it is smog exempt, licensed and registered for road use with a Montana title and plates. 1967 Camaro s/n 132178 could be the ultimate track day racer, an outrageous Sunday driver or simply look great in any collection! Priced well below the cost of building, testing and development into race-ready condition.

1967 Camaro s/n 132178 was fully rebuilt for Pike’s Peak. Every component on this camaro is new and never raced and only need final sorting and testing. Thanks to its 500 plus hp 6.6 liter (400 C.I.D.) Donovan aluminum small block and its stripped out body at 2,400 lbs this camaro is outrageously powerful and with minor tweaks can run in HSR, VARA, NASA, Targa Newfoundland or any other such similar event or series. Because this camaro is a 1967 year model it is smog exempt, licensed and registered for road use with a Montana title. 1967 Camaro s/n 132178 could be the ultimate track day racer or simply look great in any collection! Priced well below the cost of building, testing and development into race-ready condition.

S/n 12437. Chevrolet Camaro.

1967, January, build date, Van Nuys, CA. Originally Red/Red. Build date 1967, 2nd week January. Body #16809. Bolero Red. Sport Coupe, no vinyl top. Standard interior, red standard bucket seats, tinted windshield, powerglide transmission, center console, gauges or clock, deluxe seat belts.

2016–2017, rebuilt to Pike’s Peak specifications by Absolute Engineering, Goleta, CA at a hard-parts cost of well over $100,000. Never used, never raced.

2018, March, on consignment with Ferraris-Online LLC.

2018, 18 May, Serviced by Absolute Engineering.  Install fuel gauge sender, battery, belts and harnesses, new wheels and tires. New parts include wheel spacers, axle U bolts, wire dividers, battery boots, speedo drive gear, and speedo gear housing. Total invoice $5,338.00

SOCIAL MEDIA

More Cars

Top